QQ: 859818709

Opto Diode SXUV100 Broadband Photodiode, 1-1000 nm, 100 mm², Through-Hole

Opto Diode SXUV100 Broadband Photodiode, 1-1000 nm, 100 mm², Through-Hole

$1,025.00
SKU: SXUV100
Category: ,
Brands:

Description

Opto Diode SXUV100 Windowless Silicon Photodiode

The Opto Diode SXUV100 is a 100 mm² (10 mm × 10 mm) large-area, windowless silicon photodiode with a spectral response covering 1 nm to 1000 nm, designed for measuring and monitoring high-power-density sources in the extreme-ultraviolet (EUV, the 13.5 nm lithography band) and vacuum-ultraviolet (VUV). The device uses an oxide-passivated silicon junction that keeps its response stable after intense EUV/UV exposure, with a shunt resistance of ≥10 MΩ and reverse breakdown voltage ≥10 V — suited to synchrotron beamline diagnostics, plasma diagnostics, EUV lithography source monitoring and VUV spectrometers. The tax-inclusive price on this page (13% VAT included) is shown in the price box.

Product Overview

The SXUV100 belongs to Opto Diode’s SXUV series — passivated for intense EUV/UV environments, with the factory stating that the response remains stable after EUV/UV exposure. Compared with the general-purpose AXUV series it is better suited to continuous monitoring under long-term high-energy UV irradiation. Extreme-ultraviolet photons from 1 nm carry high energy and have an absorption length in air of only micrometres, so any window would cause severe attenuation; the SXUV100 therefore uses a windowless, direct-illumination structure: photons enter the silicon junction directly, avoiding both the strong absorption and the radiation darkening of window materials in the 1–200 nm band.

The active area is 10 mm × 10 mm (100 mm²), a large-area specification among EUV detectors, able to accept divergent or large-area parallel beams and relax the alignment requirement; it can also be used for rough assessments of beam uniformity and energy distribution. The trade-off is a large junction capacitance (5–15 nF at 0 V) and slow response (6 µs per the datasheet, RL = 50 Ω, VR = 8 V), so it is positioned for DC optical power, pulse energy (µs scale and above) and integrating measurements rather than nanosecond pulse waveform recovery — choose a small-area model when high-speed response is required.

The package is a 16.50 mm × 15.00 mm × 2.10 mm square structure with a 10.03 mm square active region and two leads (cathode / anode) spaced 12.50 mm apart, Ø0.45 mm diameter, for through-hole soldering or mounting on a flange or PCB. The device ships with a temporary protective cover for the chip and wire bonds, which must be removed before use per the manufacturer’s application note. The SXUV100 is made by Opto Diode Corp (an ITW company, USA); supplied original by Soar Laser, with parameters taken from the manufacturer’s datasheet (Rev. 2019-11-26) and cross-checked against public manufacturer materials (checked 2026-11-04).

Key Features

  • Detection from 1 nm: covers EUV / VUV (1–200 nm) through visible and near-infrared (to 1000 nm) in a single device
  • Windowless direct-illumination structure: no window absorption or radiation darkening, minimal energy loss in the 1–200 nm band
  • Oxide-passivated silicon junction: response remains stable after intense EUV/UV exposure — suited to long-term in-line monitoring rather than one-off measurements
  • 100 mm² active area (10 mm × 10 mm): strong light collection, insensitive to spot alignment and beam divergence
  • Shunt resistance ≥10 MΩ (@ ±10 mV), reverse breakdown ≥10 V: works in zero-bias photovoltaic mode, or with reverse bias to reduce junction capacitance
  • Low dark current: approx. 19 nA @ VR = 10 V and approx. 32 nA @ VR = 50 V (typical curves), giving a small weak-signal zero drift
  • Peak responsivity approx. 0.27 A/W @ 1 nm and approx. 0.33 A/W @ 850 nm (typical curves)
  • Square through-hole package 16.50 × 15.00 × 2.10 mm, 2 leads, easy to integrate into vacuum-flange assemblies or detector boards
  • Wide temperature range: −10 to 40 °C ambient; −20 to 80 °C in nitrogen or vacuum; maximum junction temperature 70 °C
  • RoHS compliant, MSL 1 (unlimited), ECCN EAR99 — easy export and production-line introduction

Technical Specifications

Parameter Value
Manufacturer Opto Diode Corp (an ITW company, USA)
Manufacturer part number (MPN) SXUV100
Product type Silicon photodiode (windowless)
Series SXUV (radiation-hardened EUV/UV series)
Spectral response range 1 nm – 1000 nm
EUV / VUV operating band 1 nm – 200 nm (typical application: the 13.5 nm lithography band)
Active area 100 mm² (10 mm × 10 mm)
Peak responsivity approx. 0.27 A/W @ 1 nm; approx. 0.33 A/W @ 850 nm (typical curves)
Responsivity reference points approx. 0.12 A/W @ 10 nm; approx. 0.01 A/W @ 100 nm (typical curves)
Shunt resistance ≥10 MΩ @ ±10 mV
Reverse breakdown voltage ≥10 V (IR = 1 µA)
Junction capacitance 5 nF – 15 nF @ VR = 0 V (datasheet); typical curves approx. 3.6 nF @ 0 V, approx. 1.3 nF @ 10 V
Dark current approx. 19 nA @ VR = 10 V; approx. 32 nA @ VR = 50 V (typical curves)
Response time 6 µs (RL = 50 Ω, VR = 8 V, datasheet); an earlier manufacturer announcement gives 250 ns typical
Operating temperature — ambient −10 °C to 40 °C
Operating temperature — nitrogen or vacuum −20 °C to 80 °C
Maximum junction temperature 70 °C
Lead soldering temperature 260 °C, 2.03 mm (0.080 in) from the body, ≤10 s
Package Square through-hole package, 2 leads (anode / cathode), ships with temporary protective cover
Outline dimensions 16.50 mm × 15.00 mm × 2.10 mm (.650 × .591 × .083 in)
Active region size 10.03 mm × 10.03 mm (.395 × .395 in)
Lead spacing / lead diameter 12.50 mm / Ø0.45 mm (.492 / Ø.018 in)
Mounting Through-hole (THT)
Illumination Windowless direct illumination (incident surface is the silicon chip itself)
Packaging Bulk, manufacturer standard package of 1
Part status Active
Supply / lead time Ordered to demand; manufacturer standard lead time approx. 18 weeks (subject to our confirmation)
RoHS compliance RoHS (ROHS3) compliant
Moisture sensitivity level (MSL) 1 (unlimited)
ECCN EAR99
HTSUS 8541.49.1050

Note: specification values are taken from the official Opto Diode datasheet “Photodiode 100 mm² SXUV100” (Revision November 26, 2019); the ranges for capacitance, dark current and responsivity come from the typical curves in the datasheet. The datasheet specification table gives a response time of 6 µs (RL = 50 Ω, VR = 8 V) while the manufacturer’s 2014 product announcement and some channel documents give 250 ns — the test conditions differ, so please rely on the datasheet curves and your own measurements for engineering evaluation.

Package Dimensions and Characteristic Curves

Opto Diode SXUV100 package outline and mounting dimensions (mm [inch])
Figure 1 — SXUV100 package outline and mounting dimensions: outline 16.50 × 15.00 mm, 2.10 mm thick, 10.03 mm square active region, lead spacing 12.50 mm (units mm [inch]; source: official Opto Diode datasheet)
Opto Diode SXUV100 typical photon responsivity curve (1-1000 nm)
Figure 2 — Typical photon responsivity: approx. 0.27 A/W at 1 nm, a dip near 100 nm (approx. 0.01 A/W), peak approx. 0.33 A/W near 850 nm (source: official Opto Diode datasheet)
Opto Diode SXUV100 junction capacitance versus reverse bias curve
Figure 3 — Junction capacitance vs. reverse voltage: approx. 3.6 nF at 0 V, approx. 1.3 nF at 10 V; reverse bias significantly lowers capacitance and improves response speed (source: official Opto Diode datasheet)
Opto Diode SXUV100 dark current versus reverse bias curve
Figure 4 — Dark current vs. reverse voltage: approx. 19 nA at 10 V and approx. 32 nA at 50 V; the rise is steep below 10 V, so in practice choose a bias above that knee (source: official Opto Diode datasheet)

Typical Applications

  • EUV lithography light-source monitoring: in-line measurement of 13.5 nm source energy, power and pulse stability
  • Synchrotron beamline diagnostics and beam position / intensity monitoring
  • Plasma diagnostics: EUV / VUV radiance and spatio-temporal distribution measurements
  • Detector side of VUV spectrometers and monochromators
  • UV energy meters and dose monitoring in semiconductor lithography and inspection equipment
  • Radiometry of short-wavelength sources such as high-harmonic generation (HHG) and free-electron lasers
  • Space-based UV remote sensing, radiometric calibration and scientific instruments
  • Power-density monitoring of high-power-density UV sources (1–150 nm)

Downloads

For the manufacturer application note “Handling Precautions for AXUV, SXUV, and UVG Detectors”, RoHS declarations or lot inspection reports, contact our engineers and we will request them for you.

Frequently Asked Questions (FAQ)

Q1: What is the key difference between the SXUV100 and an ordinary silicon photodiode?

A: Two things: (1) the windowless structure — extreme-ultraviolet photons from 1 nm reach the silicon directly without passing through a window, avoiding the strong absorption and radiation darkening of window materials in the 1–200 nm band; (2) the oxide-passivated silicon junction is treated for intense EUV/UV exposure, and the manufacturer states the response remains stable after such exposure. Ordinary windowed silicon PIN diodes have essentially no useful response below 200 nm.

Q2: With a 100 mm² active area, is the device too slow?

A: Yes, relatively. Junction capacitance is 5–15 nF at 0 V and the datasheet response time is 6 µs (RL = 50 Ω, VR = 8 V). It suits DC optical power, pulse energy (µs and above), integrating and quasi-DC measurements — not nanosecond pulse waveform recovery. For high speed choose a small-area model in the same series or a fast detector with a built-in electric field.

Q3: Must it be used in vacuum or nitrogen?

A: Not necessarily. The ambient operating range is −10 to 40 °C, extendable to −20 to 80 °C in nitrogen or vacuum. However VUV measurements (especially below 150 nm) must themselves be made in vacuum or with an inert-gas-purged beam path, because air absorbs strongly in that band — this is a beam-path requirement, not a device requirement. The short wavelengths are extremely sensitive to surface contamination, so handle and store the device cleanly.

Q4: Should the shipping protective cover be removed, and how?

A: Yes. The device ships with a temporary protective cover for the chip surface and wire bonds. Remove it before use as described in the manufacturer application note “Handling Precautions for AXUV, SXUV, and UVG Detectors”, taking anti-static precautions and never touching the active surface. Do not soak or wipe the active surface with solvents when cleaning, to avoid damaging the passivation layer and bond wires.

Q5: Why does the responsivity curve dip noticeably around 100 nm?

A: Silicon’s absorption length around 100 nm is extremely short, so a large share of photo-generated carriers recombine at the surface, and the surface oxide absorbs too — quantum efficiency drops into a valley (typical value about 0.01 A/W). This is inherent to silicon-based EUV/VUV detectors; the SXUV passivation improves the stability of the response in that band, not its absolute responsivity. For quantitative work, calibrate at your actual wavelength and incidence conditions first.

Q6: How do I wire the SXUV100 for 13.5 nm lithography source monitoring?

A: The common approach is to receive the beam inside the vacuum chamber at near-normal or oblique incidence, read the photocurrent with a transimpedance amplifier (TIA), or measure pulse energy with an integrating capacitor. Since responsivity varies with wavelength, incidence angle and surface condition, calibrate against a synchrotron or a standard detector before formal measurements. A bias of 5–10 V is recommended: it lowers the junction capacitance while avoiding the steep dark-current rise at low bias.

Q7: Is it in stock, what is the lead time, and what does the price include?

A: The SXUV100 is an order-to-demand item with a manufacturer standard lead time of about 18 weeks — for urgent needs check in-transit stock with us first. The tax-inclusive price shown on this page (13% VAT included) is our selling price, minimum order 1 unit; volume purchasing, matched bias supplies or transimpedance amplifiers can be quoted separately.

Further Reading

Ordering Information

Ordering model: SXUV100 (manufacturer: Opto Diode Corp). The series also includes models with different active areas (e.g. SXUV5, SXUV20HS1, SXUV63HS1) that differ significantly in area, capacitance and sensitivity — confirm the model against your spot size and bandwidth needs; they are not directly interchangeable.

For matched vacuum-flange mounting parts, transimpedance amplifiers, bias supplies, or manufacturer-screened / calibrated versions, contact our engineers for a solution and quotation.

Disclaimer

Parameters, curves and dimensions on this page are compiled from the official Opto Diode datasheet (Rev. 2019-11-26) and cross-checked against public specification material; actual product parameters, appearance and packaging follow the manufacturer’s shipment, and specifications may change without notice.

This product is an electrostatic-sensitive device with an exposed, windowless active area — handle with anti-static and cleanliness precautions. Bias, optical power density or temperature beyond the specifications may permanently damage the device; such damage is not covered by warranty.

The product is intended for lawful scientific and industrial use only.

Reviews

There are no reviews yet.

Be the first to review “Opto Diode SXUV100 Broadband Photodiode, 1-1000 nm, 100 mm², Through-Hole”

Your email address will not be published. Required fields are marked *

中文EN