Description
Product Overview
The PF05-03-P01 is a Ø12.7 mm (Ø1/2 inch) plano mirror with a protected silver coating on a fused silica substrate. Average reflectance is 97% from 450 nm to 2 µm and 95% from 2 µm to 20 µm. The disc is 6.0 mm thick, the reflecting face is figured to λ/10 peak to valley at 633 nm and polished to 40-20 scratch-dig, parallelism is held inside 3 arcmin, and clear aperture is 90% of the diameter. A laser-engraved item number sits on the back.
Silver holds the highest reflectance in the visible and near infrared of any metal film Thorlabs deposits, and the reason is where its absorption sits. The interband transitions that spoil aluminum in the blue and gold across the whole visible are pushed far into the ultraviolet for silver, so from roughly 450 nm outward the metal behaves as a nearly ideal free-electron reflector. Across 450 nm to 2 µm the curve is flat enough that Thorlabs can quote a single average figure, and it stays above 95% out to 20 µm. For a broadband fold that has to work at several laser lines at once, that flatness is worth more than a peak value at one wavelength.
The weakness of silver is chemical, not optical. Silver tarnishes in the presence of atmospheric sulfur and oxidises in humid air, and both products are dark and absorbing. Thorlabs answers this with a durable SiO₂ overcoat approximately 100 nm thick, and that layer is why this optic can be handled and cleaned like ordinary laboratory glassware. It is not a total barrier. The manufacturer states plainly that high humidity environments should be avoided, and a bay with condensation on the mounts is a bay where a protected aluminum mirror will outlast this one. Aluminum grows its own passivating oxide beneath its SiO₂ layer, so it tolerates moisture that silver does not, at the cost of several points of reflectance in the visible.
For pulsed work the coating is a reasonable default across its band. Thorlabs names femtosecond pulsed lasers as a target application, which follows from the 450 nm to 20 µm coverage: a fold mirror that reflects the pump and the signal without a coating change is what a broadband oscillator needs. Where the pulse band is narrow and centred near 800 nm, the ultrafast-enhanced silver coating on the -AG parts is the sharper tool, since it specifies 99.0% for s-polarization and 98.5% for p-polarization at 45 degrees over 750 nm to 1 µm. This part is the broadband choice, not the peak-reflectance-at-one-wavelength choice.
Metal films are relatively insensitive to angle of incidence, which is the practical reason a single part number serves both a near-normal fold and a 45 degree turn. Thorlabs publishes the reflectance curve at both 12 and 45 degrees for this reason. Nothing about the mount changes when the geometry does, so the same mirror can be moved from a periscope to a turning mirror without a new specification.
Key Features
- Highest visible and near infrared reflectance of the metal coatings: 97% average from 450 nm to 2 µm, flat enough to serve several laser lines without a coating change
- 95% average from 2 µm to 20 µm, so one part number spans 532 nm alignment, 1064 nm working beams and CO2 wavelengths
- SiO₂ overcoat roughly 100 nm thick against tarnish and oxidation, which is what makes the surface wipeable with standard optics procedure
- Fused silica substrate, 12.7 mm diameter by 6.0 mm thick, tolerances +0.0 / -0.1 mm and ±0.2 mm
- λ/10 peak to valley at 633 nm with 40-20 scratch-dig and parallelism inside 3 arcmin, for wavefront-sensitive folding
- Clear aperture 90% of the diameter, leaving a coated annulus for edge-grip mounting
- Low angle sensitivity: the manufacturer publishes the curve at 12 and 45 degrees because a 45 degree fold needs no separate design
- Humidity is the one caveat: the overcoat slows tarnish but Thorlabs advises against high humidity environments
Technical Specifications
| Parameter | Value |
|---|---|
| Model | PF05-03-P01 |
| Coating | Protected silver with SiO₂ overcoat, approximately 100 nm |
| Wavelength range | 450 nm – 20 µm |
| Average reflectance | 97% for 450 nm – 2 µm; 95% for 2 µm – 20 µm |
| Substrate | Fused silica |
| Diameter | 12.7 mm (Ø1/2 inch) |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Thickness | 6.0 mm (0.24 inch) |
| Thickness tolerance | ±0.2 mm |
| Front surface flatness | λ/10 peak to valley at 633 nm |
| Surface quality | 40-20 scratch-dig |
| Parallelism | 3 arcmin or less |
| Clear aperture | 90% of the diameter |
| Damage threshold, pulsed | 0.225 J/cm² at 800 nm, 99 fs, 1 kHz, Ø0.167 mm; 1 J/cm² at 1064 nm, 10 ns, 10 Hz, Ø1.010 mm |
| Damage threshold, CW | 500 W/cm at 1.07 µm, Ø0.974 mm; 1500 W/cm at 10.6 µm, Ø0.339 mm |
| Cleaning | Standard optics procedure; the SiO₂ overcoat permits wiping |
| Environment | Avoid high humidity; the overcoat slows but does not stop tarnish |
| Source | Thorlabs official series specification table |
Applications
This coating is specified where the beam spans the visible and the near infrared and the fold count is high enough that a dielectric stack per wavelength would be unmanageable.
- White-light and low-coherence interferometry: a flat reflectance curve from 450 nm to 2 µm keeps the envelope symmetric instead of weighting one end of the spectrum
- Fluorescence microscope excitation paths: folding 405, 488, 561 and 640 nm lines through one mirror without swapping coatings
- Multi-line laser combining: 532 nm, 633 nm, 780 nm and 1064 nm sharing a single fold train in a Raman or pump-probe bench
- Femtosecond oscillator folding: broadband coverage across pump and signal, which is the application Thorlabs names for the coating
- Spectrometer and monochromator relay optics: visible throughput is the figure of merit and 97% average is the highest a metal film offers
- Structured light and machine vision projection: folding a white LED or supercontinuum source where the visible band has to stay balanced
Selection Guide
Four coatings cover the same half-inch envelope, and the decision is driven by band first and environment second.
| Coating | Best band | Average reflectance | Choose it when |
|---|---|---|---|
| Protected silver, -P01 | 450 nm – 20 µm | 97% / 95% | The beam is visible or near infrared and humidity is controlled |
| Protected aluminum, -G01 | 450 nm – 20 µm | 90% / 95% | The bay is humid, condensing or industrial and a few points of visible reflectance can be spared |
| Protected gold, -M01 | 800 nm – 20 µm | 96% | The beam is infrared only and the flat gold curve is preferable above 2 µm |
| UV enhanced aluminum, -F01 | 250 nm – 450 nm | 90% | The beam is ultraviolet, where silver has already collapsed |
The crossover that catches people out is the short-wavelength end. Below about 450 nm silver reflectance falls steeply, so a 405 nm or 355 nm line needs the UV enhanced aluminum PF05-03-F01 and not this part. At the long end there is no such cliff: this mirror is specified all the way to 20 µm, though above 2 µm the gold coatings carry the higher figures. If the visible reflectance is not needed at all, the protected gold PF05-03-M01 is the more durable infrared choice.
Series Comparison
The protected silver round mirrors share one specification and differ only in aperture and thickness, which matters when a mount is already fixed and only the diameter is in question.
| Item number | Diameter | Thickness | Average reflectance | Typical mount |
|---|---|---|---|---|
| PF03-03-P01 | 7.0 mm (0.28 inch) | 2.0 mm | 97% / 95% | Compact and OEM modules |
| PF05-03-P01 | 12.7 mm (0.5 inch) | 6.0 mm | 97% / 95% | Half-inch kinematic mounts |
| PF07-03-P01 | 19.0 mm (0.75 inch) | 12.0 mm | 97% / 95% | Polaris fixed mounts for OEM design |
| PF10-03-P01 | 25.4 mm (1.0 inch) | 19.1 mm (0.75 inch) | 97% / 95% | One-inch kinematic mounts |
The 19.0 mm size exists specifically to fit Polaris fixed optic mounts for laser system design and OEM production, which is the size to reach for when a half-inch aperture clips a beam that has already been expanded. Square versions of the same coating are sold as PFSQ05-03-P01 and larger, and a rectangular variant with a different silver process is the PFR14-P02. Above 25.4 mm the thickness climbs quickly, so check the mount depth before stepping up an aperture class.
FAQ
Silver or gold? Silver if the beam reaches into the visible, because gold is not specified below 800 nm and would simply absorb a 532 nm line. Gold if the beam lives entirely in the infrared, because its curve is flatter above 2 µm and the film is more forgiving of a humid bay.
Can this mirror be cleaned? Yes. The SiO₂ overcoat is there to make it cleanable, and standard optics procedure with solvent and lens tissue applies. That is the practical difference between this part and the unprotected gold mirror, which cannot be touched at all.
Will it tarnish in a humid room? The overcoat slows tarnish substantially, but Thorlabs explicitly advises against high humidity environments. A climate-controlled laboratory is fine. An unheated workshop with condensation on the hardware is not, and protected aluminum is the safer specification there.
Why does the reflectance drop above 2 µm? The free-electron response weakens and absorption rises, so the average falls from 97% to 95%. The optic is still specified to 20 µm, which is why it can serve a CO2 alignment beam in the same train as a 633 nm pointer.
Is it suitable for femtosecond pulses? Thorlabs lists femtosecond pulsed lasers among the applications, on the strength of the broadband coverage. For a narrow band near 800 nm the ultrafast-enhanced silver coating is the better specified option, since it quotes separate s and p figures at 45 degrees.
Does the reflectance change at 45 degrees? Very little. Metal films are relatively insensitive to angle of incidence, and the manufacturer publishes the curve at both 12 and 45 degrees to show it. A turning mirror and a near-normal fold can use the same part number.
Is there a ten-piece pack? Yes, the PF05-03-P01-10 contains ten of this optic. For a single fold, buy the single.
Usage Precautions
- Handle by the edge with gloves; the overcoat resists cleaning but does not make fingerprints harmless
- Clean with standard optics procedure only, using solvent and lens tissue, and never dry-wipe a dusty surface
- Keep the optic out of high humidity and away from sulfur-bearing atmospheres, which are what tarnish silver
- Seat the mirror with light pressure only; over-tightening a retaining ring distorts a 6.0 mm disc and shows up as wavefront error
- Do not expose the coating to plasmas, reactive ion environments or adhesive residues, all of which attack the overcoat
- The pulsed rating of 0.225 J/cm² is quoted at 99 fs over a 0.167 mm spot; scale it by beam area before applying it to another pulse duration
Disclaimer
Specifications here are transcribed from the Thorlabs protected silver mirror series specification table for selection purposes. The official datasheet in force at the time of purchase governs, and the manufacturer may revise figures or processes without notice. Reflectance values are averages over the stated bands; performance outside those bands is typical rather than guaranteed and varies between coating runs. Lead time and price are quoted by our sales team against live stock.
Contact Us
Changsha Soar Laser Equipment Co., Ltd. supplies genuine Thorlabs optics to laboratories and machine builders in China. Silver against aluminum is the question we are asked most often, and it is usually settled by two facts: the shortest wavelength in the beam and the humidity of the room the hardware lives in. Send us both and we will recommend one, not a list. Hotline +86 159 2722 0467, email 859818709@qq.com, website www.soar-laser.cn.









Reviews
There are no reviews yet.