QQ: 859818709

Thorlabs PF05-03-M01 Ø1/2″ Protected Gold Mirror, 800 nm – 20 µm

Thorlabs PF05-03-M01 Ø1/2″ Protected Gold Mirror, 800 nm – 20 µm

Price on request
Category:

Description

Product Overview

The PF05-03-M01 is a Ø12.7 mm (Ø1/2 inch) plano mirror carrying Thorlabs protected gold coating on a fused silica substrate. Average reflectance is above 96% across 800 nm to 20 µm, the substrate is 6.0 mm thick, the reflecting face is figured to λ/10 peak to valley at 633 nm and polished to 40-20 scratch-dig, and parallelism is held to 3 arcmin or better. Clear aperture is more than 90% of the diameter.

Gold is the one metal film that carries reflectance from the near infrared to the thermal infrared without changing coating. Its useful range begins where the interband absorption of the metal gives way, which is why Thorlabs specifies this coating from 800 nm, and it runs to 20 µm, so a single part number covers 1064 nm and 1550 nm diode and fiber sources at one end and CO2 lasers, quantum cascade sources and thermal imagers at the other. Across that span the reflectance curve is flat and the angle sensitivity is low, because a metal reflects through its free electrons rather than through interference in a stack. Thorlabs publishes the curve at both 12° and 45° angle of incidence for exactly this reason: a 45° fold does not need a separate coating design.

What separates this from the bare gold mirror is the dielectric overcoat deposited on the film. Gold itself is chemically inert and does not oxidise in air, but the bare film is soft enough that a fingerprint, an aerosol droplet or a wipe leaves a permanent mark. The overcoat is what lets the optic be handled and cleaned like any other mirror, and it is why this is the default fold mirror in a working laboratory rather than a specialist item. The overcoat is not free: it absorbs slightly in the mid and far infrared and it introduces a polarization change at oblique incidence that is difficult to quantify. That is the honest reading of the two datasheets, where this coating is quoted at 96% and the bare gold at 97%.

It is not a visible or ultraviolet mirror. The specification starts at 800 nm; below that the reflectance of gold falls away and the part is not specified there. A 633 nm helium-neon beam used for bore-sighting will still return light, but if the visible beam carries power the correct part is a protected aluminum mirror such as the PF05-03-G01, which is specified from 450 nm, or a protected silver mirror for the visible and near infrared.

Mechanically the part is the standard half-inch envelope: 12.7 mm diameter with a +0.0 / -0.1 mm tolerance and 6.0 mm ± 0.2 mm thickness, which is what half-inch fixed and kinematic mounts and lens-tube retainers are built around. The back face is laser engraved with the part number, so a mirror that has left its packaging can still be identified. The same coating is sold as Ø7.0 mm rounds (on a 2.0 mm substrate rather than 6.0 mm), as Ø19 mm, Ø1 inch and Ø2 inch rounds, and in three square sizes; Thorlabs also offers it on Zerodur where thermal expansion has to be very low.

Key Features

  • Protected gold film: average reflectance above 96% from 800 nm to 20 µm, with the curve published at 12° and at 45° angle of incidence
  • Dielectric overcoat on the gold: the surface can be handled and cleaned, which a bare gold film cannot
  • Low angle sensitivity: a metal film reflects through free electrons, so a 45° fold and a near-normal reflection use the same coating
  • Figure and finish: λ/10 peak to valley at 633 nm, 40-20 scratch-dig, parallelism 3 arcmin or better, clear aperture above 90% of the diameter
  • Laser ratings: 2 J/cm² at 1.064 µm for 10 ns pulses at 10 Hz over Ø1.000 mm; 500 W/cm CW at 1.070 µm and 750 W/cm CW at 10.6 µm
  • Mechanical envelope: 12.7 mm diameter on a 6.0 mm fused silica substrate, tolerances +0.0 / -0.1 mm and ±0.2 mm, part number engraved on the back
  • Whole family available: five round diameters from Ø7.0 mm to Ø2 inch, three square sizes, and a 10-piece pack of the half-inch size for builds that consume several

Technical Specifications

Parameter Value
Model PF05-03-M01
Coating Protected gold, dielectric overcoat
Wavelength range 800 nm – 20 µm
Average reflectance over 96% from 800 nm to 20 µm
Reflectance curves Published at 12° and 45° angle of incidence
Substrate Fused silica
Diameter 12.7 mm (Ø1/2 inch)
Diameter tolerance +0.0 mm / -0.1 mm
Thickness 6.0 mm (0.24 inch)
Thickness tolerance ±0.2 mm
Front surface flatness λ/10 peak to valley at 633 nm
Surface quality 40-20 scratch-dig
Parallelism 3 arcmin or better
Clear aperture above 90% of the diameter
Damage threshold, pulsed 2 J/cm² at 1.064 µm, 10 ns, 10 Hz, Ø1.000 mm
Damage threshold, CW 500 W/cm at 1.070 µm, Ø0.089 mm; 750 W/cm at 10.6 µm, Ø0.339 mm
Source Thorlabs official series specification table

Applications

This is the fold mirror that most infrared benches end up using, because one part number covers the pump arm, the signal arm and the alignment path as long as none of them is visible. The list below is what customers actually order it for.

  • 1064 nm and 1550 nm beam delivery: 45° folds in a fiber-to-free-space launch, a periscope or a beam dump line, where a 2 J/cm² nanosecond rating is far above what a seeded oscillator delivers
  • CO2 laser benches: the 10.6 µm end of the band, with 750 W/cm CW available for folding a beam into a marking or cutting head
  • FTIR and thermal imaging relays: one coating spans 2 µm to 20 µm, so a multi-element relay does not need a different mirror for each band
  • Pump-probe benches: an 800 nm Ti:sapphire arm and a mid-infrared OPA arm can share the same fold mirror, because both sit inside the specified range
  • Delay lines and multi-pass assemblies: several mirrors in one housing, where the pack version keeps the parts identical
  • Infrared system alignment: the engraved back face identifies the optic after the mount has been closed and the bench is under purge

Selection Guide

The three gold coatings Thorlabs sells on this 12.7 mm substrate differ only in band and reflectance. Read the table by the band the beam actually occupies, not by the highest number in the row.

Coating Suffix Wavelength range Average reflectance
Protected gold -M01 800 nm – 20 µm over 96%
MIR enhanced gold -M02 2 µm – 20 µm over 98%
Unprotected gold -M03 800 nm – 20 µm over 97%

The judgement for this page is simple: if the path carries anything between 800 nm and 2 µm, the -M01 is the right coating, because it is the only gold that is specified there. If the path is entirely beyond 2 µm and two extra points of reflectance per bounce are worth having, the PF05-03-M02 is the better part. If the application is ultrafast or polarization sensitive, the PF05-03-M03 removes the overcoat entirely and gives up the last point of robustness in exchange. For visible work, step outside the gold family: protected aluminum covers 450 nm to 20 µm, and a Ø7.0 mm protected silver mirror gives the highest visible and near-infrared reflectance in the range, though only in the smaller 7.0 mm diameter.

FAQ

Can I use this mirror with a 633 nm alignment laser? The coating is specified from 800 nm upward and gold reflectance falls away below that, so a red beam comes back weak and the part is outside its specification there. For bore-sighting that is usually acceptable; if the visible beam carries power, use the PF05-03-G01 protected aluminum mirror instead.

How should I clean the protected gold surface? The overcoat is the reason cleaning is possible at all. Blow off loose dust first, then use a single pass of lens tissue with solvent and lift it away, rather than rubbing in circles; never dry-wipe grit across the coating. Solvent residue is removed with a clean dry pass.

Is the 10-pack a different optic? No. The PF05-03-M01-10 is ten of this exact mirror under one part number, with the same coating, substrate and tolerances. It exists because a multi-mirror assembly is easier to build from one delivery than from ten order lines.

The pulsed rating is quoted at 1.064 µm. What happens at 1550 nm? Thorlabs scales nanosecond thresholds with the square root of the wavelength, so a longer wavelength gives a higher threshold than 2 J/cm². Treat that as a design estimate rather than a specification: tell us the pulse energy, duration and spot size and we will confirm the margin before you order.

Does a 6.0 mm thick half-inch mirror fit standard mounts? Yes. 12.7 mm diameter with a +0.0 / -0.1 mm tolerance and 6.0 mm ± 0.2 mm thickness is the standard half-inch optic envelope that fixed mounts, kinematic mounts and lens-tube retainers are sized for.

Disclaimer

The figures on this page are transcribed from Thorlabs published specification tables and are offered as a selection aid, not as a substitute for the current official datasheet, which remains authoritative and may be revised without notice. Coating appearance and marking may differ between production runs. Commercial terms and delivery dates are confirmed by our sales team against live stock at the time of order.

Contact Us

Changsha Soar Laser Equipment Co., Ltd. supplies genuine Thorlabs optics to laboratories and machine builders in China. For coating selection, aperture sizing, mount matching or availability of a specific part number, contact us: hotline +86 159 2722 0467, email 859818709@qq.com, or the enquiry form on www.soar-laser.cn. Send the wavelength, the beam diameter at the mirror and the pulse energy or continuous power, and we will confirm that protected gold is the correct film before the order is placed.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF05-03-M01 Ø1/2″ Protected Gold Mirror, 800 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN