QQ: 859818709

Thorlabs PF07-03-P01 Ø19.0 mm Protected Silver Mirror, 450 nm – 20 µm

Thorlabs PF07-03-P01 Ø19.0 mm Protected Silver Mirror, 450 nm – 20 µm

Price on request
Category:

Description

Product Overview

The Thorlabs PF07-03-P01 is a Ø19.0 mm silver mirror sealed under a silica overcoat, specified above 97% average reflectance from 450 nm to 2 µm and above 95% from 2 to 20 µm, on a 6.0 mm fused silica substrate figured to λ/10 peak to valley at 633 nm. Of the five coatings on this substrate it is the brightest in the band where most lasers and most cameras actually work.

That brightness is a property of the metal, not of the coating process. Silver has the highest reflectance of any metal across the visible and near infrared, which is why it was the standard mirror coating long before vacuum deposition made aluminium practical. Its weakness is at the short end: the plasma edge sits in the deep ultraviolet, so reflectance drops steeply below roughly 400 nm and a silver mirror is a poor choice for a 355 nm beam no matter how good the polish is. Between 450 nm and 2 µm, however, nothing else in this group comes close.

The failure mode of silver in service is chemical rather than mechanical. Silver sulfides and tarnishes in ordinary air, turning yellow-brown and losing reflectance from the surface inward, and this is the reason plain silver mirrors were largely displaced. Thorlabs answers it with a durable silica overcoat approximately 100 nm thick, applied specifically to protect the silver from oxidation. The same page states the limit of that protection: although the overcoat helps, high humidity environments should be avoided. A silver mirror is therefore a considered choice for a climate-controlled laboratory, and a protected aluminium mirror is the safer one for a workshop.

The 19 mm format belongs to the Polaris fixed mount, and a visible path is where a fixed mount is least intrusive. A beam at 532 nm or 450 nm can be seen on a card, so alignment is done by watching the spot rather than by measuring; what the hardware has to provide is a seat that repeats and a holder that does not put a shadow across the aperture. The POLARIS-19S50/M clamps a 6 mm thick, 19 mm optic on three axial points within a Ø1 inch footprint, leaving the 17 mm clear aperture unobstructed.

Key Features

  • 97% from 450 nm to 2 µm: the highest visible and near-infrared reflectance of any metal coating in this group, and the only reason to accept silver’s handling constraints
  • Roughly 100 nm silica overcoat: applied to stop the oxidation and sulfidation that destroy unprotected silver, and the reason this mirror can be cleaned at all
  • Femtosecond rating published: 0.225 J/cm² at 800 nm with 99 fs pulses at 1 kHz, alongside the nanosecond figure
  • 1 J/cm² at 1064 nm: measured with 10 ns pulses at 10 Hz over Ø1.010 mm, with CW ratings of 500 W/cm at 1.070 µm and 1500 W/cm at 10.6 µm
  • Suited to short-pulse work by design: Thorlabs notes that the high reflectance across 450 nm to 20 µm makes these mirrors well suited to femtosecond pulsed lasers
  • Ø19.0 mm x 6.0 mm: λ/10 at 633 nm, 40-20 scratch-dig, parallelism within 3 arcmin, clear aperture 90% of diameter

Technical Specifications

Model PF07-03-P01
Coating Protected silver
Overcoat Silica (SiO₂), approximately 100 nm
Wavelength range 450 nm – 20 µm
Average reflectance above 97% from 450 nm to 2 µm; above 95% from 2 to 20 µm
Substrate Fused silica
Diameter Ø19.0 mm (0.75 in)
Diameter tolerance +0.0 mm / -0.1 mm
Thickness 6.0 mm (0.24 in)
Thickness tolerance +/-0.2 mm
Clear aperture 90% of diameter, about Ø17.1 mm
Surface flatness λ/10 peak to valley at 633 nm
Surface quality 40-20 scratch-dig
Parallelism at most 3 arcmin
Pulsed damage threshold 1 J/cm² at 1064 nm (10 ns, 10 Hz, Ø1.010 mm); 0.225 J/cm² at 800 nm (99 fs, 1 kHz, Ø0.167 mm)
CW damage threshold 500 W/cm at 1.070 µm (Ø0.974 mm); 1500 W/cm at 10.6 µm (Ø0.339 mm)
Environment avoid high humidity even with the overcoat fitted
Cleanable Yes
Source Thorlabs official series specification table

Applications

The pattern here is high throughput in the visible and near infrared, often with a beam the user can see, and often with a short pulse that punishes a lossy coating more than a continuous one.

  • 532 nm and 450 nm beam folding: high-power green and blue diode-pumped and direct diode sources, where a five point reflectance advantage per reflection becomes a measurable difference in delivered power
  • Microscopy and imaging relay: fluorescence and confocal paths where every reflection sits between the sample and a detector that is already photon-starved
  • Laser display and projection engines: combining and folding red, green and blue channels, where a neutral, high and flat visible reflectance keeps colour balance stable across the field
  • Femtosecond oscillator and amplifier routing: the 800 nm nanosecond and femtosecond ratings cover the two pulse regimes Ti:sapphire work actually uses
  • Broadband visible and near-infrared spectroscopy: a bench running 450 nm to 2 µm with a white-light or supercontinuum source, where a coating with a spectral feature would appear as a false absorption band

Selection Guide

  • Take silver when the band is 450 nm to about 1.1 µm and throughput is the priority: this is the only coating here that reaches 97% in that window, and the margin over protected aluminium is large enough to matter in an imaging or display path
  • Change to gold beyond 2 µm: silver’s advantage disappears at long wavelength and its curve declines, while gold stays flat. A 10.6 µm beam belongs on the protected gold page
  • Change to aluminium in a humid or dirty environment: the overcoat slows tarnish but does not stop it, and Thorlabs advises against high humidity. A machine shop or an unheated building is not where a silver mirror belongs
  • Do not use it below 400 nm: reflectance falls steeply there. A 405 nm laser diode sits on the edge of the specification, and a 355 nm beam needs the UV-enhanced aluminium item
  • Account for the number of reflections: at 97% per bounce, ten folds keep 74% of the beam; at 90% they keep 35%. The cost difference between silver and aluminium is small next to the power difference in a many-fold layout

Series Comparison

Silver and aluminium are the two broadband options and they overlap almost completely in band, so the comparison comes down to where each one wins and what each one costs in maintenance.

Item Coating Wavelength range Average reflectance Overcoat Where it wins
PF07-03-P01, this page Protected silver 450 nm – 2 µm; 2 – 20 µm 97% / 95% SiO₂, about 100 nm Brightest visible and near-infrared image
PF07-03-G01 Protected aluminium 450 nm – 2 µm; 2 – 20 µm 90% / 95% SiO₂ Humid rooms, cost, rough handling
PF07-03-M01 Protected gold 800 nm – 20 µm 96% Dielectric Flat curve above 800 nm, high power
PF07-03-M02 MIR-enhanced gold 2 – 20 µm 98% average, 95% absorption-weighted Dielectric, MIL-C-48497A Mid-infrared sensing, low power
PF07-03-F01 UV-enhanced aluminium 250 – 450 nm above 90% MgF₂ Anything below 450 nm

The same silver coating is stocked in smaller formats: Ø1/2 inch protected silver, Ø7.0 mm protected silver, and the low-expansion Zerodur protected silver mirror.

FAQ

Does the overcoat stop the mirror tarnishing permanently? It slows it substantially and it is the reason the mirror can be sold at all, but Thorlabs still advises against high humidity environments. Treat the coating as protection against normal laboratory air, not as a hermetic seal. In a humid climate, store the optic with desiccant and inspect the surface periodically for a yellow cast.

Why 97% and not the 99% a dielectric mirror achieves? A dielectric stack can reach 99% or better, but only inside the band it was designed for and usually only near a stated angle. A metal coating holds 97% across 450 nm to 2 µm and is comparatively insensitive to incidence angle. The dielectric wins on a single narrow line; the metal wins when the wavelength or the geometry moves.

Is it suitable for femtosecond pulses? Yes. Thorlabs publishes a femtosecond threshold of 0.225 J/cm² at 800 nm with 99 fs pulses at 1 kHz, and notes that the high reflectance across 450 nm to 20 µm makes these mirrors well suited to femtosecond lasers. Note that the rating is for the stated pulse duration; a 10 fs pulse needs its own calculation.

What about 405 nm? 405 nm sits at the edge of the specified band and close to where silver reflectance begins to fall. It will work, but the margin is gone and the number quoted for 450 nm no longer applies. For a 405 nm build, either measure the mirror at that wavelength or move to the UV-enhanced aluminium coating, which is specified from 250 nm.

How does it compare with protected aluminium in a humid laboratory? Aluminium is the more forgiving of the two. Thorlabs states that the protected aluminium coating has a smaller chance of tarnishing than protected silver in a high humidity environment. The trade is about seven percentage points of visible reflectance, so the decision is whether the throughput matters more than the environment.

Usage Precautions

  • Keep humidity down: the overcoat is the defence against tarnish, and humidity is what defeats it. Store the optic in a case with desiccant, and avoid leaving it mounted in an unenclosed purge box that cycles between wet and dry
  • Clean gently and rarely: silver under a 100 nm silica layer is softer than a protected aluminium coating. Blow off particles, then use solvent on a tissue with a single drag. Do not polish, and do not use abrasive lens papers
  • Inspect for a yellow cast: a silver mirror that has begun to tarnish looks warm in reflection before any meter will show it. Check the surface at each service interval rather than waiting for a power drop
  • Respect the angle: reflectance curves are published at 12 and 45 degrees. A steeply folded path beyond 45 degrees moves off the characterised data, and s and p polarisations diverge further as the angle increases
  • Hold by the edge only: fingerprints on a silver coating leave an organic residue that both scatters and accelerates local tarnish. Finger cots are not optional on this optic
  • Do not substitute it into a high-power infrared process: the 1500 W/cm rating at 10.6 µm is generous, but silver is specified only to 20 µm and the curve declines toward that end. A CO2 process beam belongs on protected gold

Disclaimer

Specifications on this page are compiled from Thorlabs official published material and are provided as a selection reference. The current official specification sheet governs; specifications and appearance may change without notice. Price and lead time are quoted by our sales team on request.

Contact Us

Changsha Soar Laser Equipment Co., Ltd. stocks Thorlabs metallic mirrors and can advise on silver versus aluminium for a specific environment and band. Hotline +86 159 2722 0467, email 859818709@qq.com, website www.soar-laser.cn.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF07-03-P01 Ø19.0 mm Protected Silver Mirror, 450 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN