Description
Product Overview
The Thorlabs PF07-03-P01P is a Ø19.0 mm plano mirror in the back-side-polished family. A protected silver film covers the front face over the 450 nm to 20 µm band; the front is figured to λ/10 at 632.8 nm with 10-5 scratch-dig, and the rear face is polished to λ/4 at 632.8 nm with 40-20 scratch-dig. The substrate is fused silica, 6.0 mm thick with a ±0.2 mm tolerance, the clear aperture is Ø17.1 mm, and the part is specified for incidence angles from 0 to 45 degrees.
A back-side-polished mirror exists for exactly one reason: it lets you watch the beam while it turns the beam. No metal film is perfectly opaque. Inside the coating band a small fraction of the incident light passes through the silver, crosses the substrate and reaches the rear face. On an ordinary mirror that face is fine ground, so the light leaves as a wide scatter and is lost. Here the rear face is an optical surface held to λ/4, so the transmitted light leaves as a collimated, low-divergence beam that can be caught on a photodiode a few centimetres behind the mount. The manufacturer quotes this leakage as much less than one percent of the incident power across the band, which is too little to disturb the reflected beam and enough to drive a biased detector.
The two faces are specified to different standards because they do different jobs. The front face carries the beam quality of the reflected path, so it gets the tight figure and the tight scratch grade: λ/10 and 10-5. The rear face never touches the working beam; it only has to deliver a collectable sample and to make its own reflection a clean, predictable ghost, so λ/4 and 40-20 is the right amount of money to spend there. Reading the datasheet the other way round, as though the rear face were the inferior one, misses the point of the part.
Compared with the PF07-03-P01, the ordinary frosted-back protected silver mirror in the same 19 mm format, the coating, substrate, thickness and angular range are identical. Two things differ: the front face here is 10-5 instead of 40-20, and the rear face is polished instead of fine ground. If you want the fold and nothing else, the frosted version is cheaper and produces no rear beam to block. If you want the fold plus a sample of the beam, this is the part.
Key Features
- Rear face polished to λ/4 at 632.8 nm, 40-20 scratch-dig: this is the sampling surface, not a cosmetic finish, and it is the only reason the part costs more than the frosted version
- Well below one percent transmission across 450 nm to 20 µm: enough to drive a photodiode with a transimpedance amplifier, far too little to measurably dim the reflected beam
- Front face at λ/10 with 10-5 scratch-dig: one scratch grade better than the frosted-back PF07-03-P01 carrying the same silver film
- Protected silver, 96% average from 400 to 700 nm and 97.5% from 700 nm to 2 µm: the highest broadband reflectance of any metal film in this size, specified from 0 to 45 degrees
- Ø19.0 mm body, Ø17.1 mm clear aperture: the Polaris fixed-mount format, which gives a Ø1 inch mounting footprint with more clear aperture than a Ø1/2 inch optic allows
- 6.0 mm ±0.2 mm fused silica: stiff enough that the three-point flexure seat of a fixed mount holds it without inducing figure error
Technical Specifications
| Model | PF07-03-P01P |
| Coating | Protected silver (silver film with protective overcoat) |
| Wavelength range | 450 nm – 20 µm |
| Average reflectance | Ravg 96% from 400 to 700 nm; Ravg 97.5% from 700 nm to 2 µm; above 95% out to 20 µm |
| Angle of incidence | 0 to 45 degrees |
| Substrate | Fused silica |
| Diameter | Ø19.0 mm (0.75 in) |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Thickness | 6.0 mm (0.24 in) |
| Thickness tolerance | ±0.2 mm |
| Front surface flatness | λ/10 at 632.8 nm over the clear aperture |
| Front surface quality | 10-5 scratch-dig |
| Rear surface flatness | λ/4 at 632.8 nm over the clear aperture |
| Rear surface quality | 40-20 scratch-dig |
| Clear aperture | Ø17.1 mm |
| Rear transmission | Well below 1% inside the coating band; intended for sampling only |
| Mounting | Polaris fixed optic mounts for Ø19 mm optics |
| Damage threshold | Coating-level rating for the protected silver film: 0.225 J/cm² at 800 nm (99 fs, 1 kHz); 1 J/cm² at 1064 nm (10 ns, 10 Hz); CW 500 W/cm at 1.07 µm and 1500 W/cm at 10.6 µm |
| Source | Thorlabs official series specification table |
Applications
- Power monitoring at a fold you already have: the sampling happens on the mirror that was going to be in the layout anyway, so the monitor costs one photodiode and no optical element
- Closed-loop power stabilisation: the rear photodiode feeds an AOM driver or a pump current controller, holding delivered power constant without interrupting the working path
- Pickoff ahead of a workpiece or a detector: measure what actually arrives at the end of the delivery path rather than what left the laser
- Diagnostics where a beamsplitter would spoil the measurement: a pickoff plate adds two surfaces, a wedge and a wavefront of its own; the polished rear face adds none of that to the reflected beam
- OEM laser heads: one part number replaces a fold mirror plus a beamsplitter plus the alignment labour of setting the beamsplitter up
Selection Guide
| Requirement | Part | Why |
|---|---|---|
| Fold the beam and sample it, broadband | PF07-03-P01P (this page) | Rear face polished to λ/4; under one percent leaks through to the rear |
| Fold the beam, no sampling, lowest cost | PF07-03-P01 | Same silver film and substrate, frosted rear face, front face at 40-20 |
| Highest reflectance from 400 to 750 nm | BB07-E02P | Broadband dielectric, 99% average, rear face also polished |
| Highest reflectance from 750 to 1100 nm | BB07-E03P | Broadband dielectric, 99% average, rear face also polished |
| The same sampling trick in a one inch optic | PF10-03-P01P | Same coating and rear polish, Ø25.4 mm body |
Series Comparison
| Item | Coating | Band | Reflectance | Front face | Typical role |
|---|---|---|---|---|---|
| PF07-03-P01P | Protected silver, rear polished | 450 nm – 20 µm | 96% / 97.5% | 10-5 | Fold plus rear sampling |
| PF07-03-P01 | Protected silver, rear frosted | 450 nm – 20 µm | 97% / 95% | 40-20 | Fold only |
| PF07-03-F01 | UV-enhanced aluminium | 250 – 450 nm | 90% | 40-20 | Ultraviolet fold |
| PF07-03-G01 | Protected aluminium | 450 nm – 20 µm | 90% / 95% | 40-20 | Humid or wipe-heavy areas |
| PF07-03-M01 | Protected gold | 800 nm – 20 µm | 96% | 40-20 | Infrared fold |
| PF07-03-M02 | MIR-enhanced gold | 2 – 20 µm | 98% | 40-20 | Mid-infrared fold |
| PF07-03 | None (blank) | Uncoated | Not applicable | 10-5 | Custom coating |
FAQ
Q: How much light really comes out of the rear face?
A: Much less than one percent of the incident power inside the coating band. For a one watt beam that is a handful of milliwatts at most, which a photodiode with a transimpedance amplifier reads comfortably. Do not design to a single number: the leaked fraction varies across the band and with incidence angle, so characterise your own part with your own photodiode before you close a control loop.
Q: So I do not need a beamsplitter for the power monitor?
A: That is the entire point of the part. A pickoff plate brings two extra surfaces, a wedge, a mechanical degree of freedom and its own transmitted wavefront into a path that was already aligned. Sampling through a polished rear face adds a detector and nothing else to the beam path.
Q: Why is the rear face only λ/4 when the front is λ/10?
A: Because the rear face does not carry the beam your experiment uses. It has to do two things: deliver a sample tight enough to land on a small detector several centimetres away, and make its own reflection a clean ghost that you can predict and block. λ/4 with 40-20 does both. Spending λ/10 money on the rear face would buy nothing you can measure.
Q: What are the drawbacks of a polished rear face?
A: Three, and all three are manageable. The rear reflection is a real stray beam, so block it. The front and rear reflections can interfere, and with a narrow-line laser on a parallel plate that shows up as fringes in the sampled signal. And the sampled beam is laterally displaced by the substrate thickness, so place the detector to suit the geometry rather than assuming it sits on the axis.
Q: How should the silver surface be handled?
A: Gloves, edges only, never the coated face. Blow off dust with dry gas before anything else. If a wipe is unavoidable, use a solvent drag wipe with lens tissue, once, in one direction. Store the optic dry and at room temperature; fingerprints and humid air attack the overcoat and then the silver underneath it.
Q: Can I use it at normal incidence as well as at 45 degrees?
A: Yes. The part is specified from 0 to 45 degrees, and a metal film changes reflectance only gradually with angle, so the same optic serves a near-normal pickoff and an oblique fold. What does change with angle is the leaked fraction and the position of the rear beam, so re-check the detector placement when you change the geometry.
Usage Precautions
- Block the rear beam. A polished rear face puts a second, lower-power beam into the lab, and it travels in a direction nobody planned for. A beam dump behind the mount is not optional.
- Expect interference. Front and rear reflections from a plane-parallel plate interfere; with a narrow-line source this appears as fringes on the sampled signal. If that matters, angle the optic slightly or accept and average the fringes.
- Stay inside 45 degrees. Beyond the specified range the reflectance and the leaked fraction both move away from the datasheet values.
- Do not over-clamp. The mount contacts the optic at three points; finger-tight is the specification, and a distorted substrate distorts both the reflected beam and the sample.
- Keep silver dry. Condensation, fingerprints and long storage in humid air degrade the overcoat first and the silver second, and the failure is not reversible.
Disclaimer
Specifications on this page are compiled from the manufacturer’s published series tables and are provided for selection purposes only. The current official datasheet governs. Dimensions, coatings and markings may change without notice. Price and delivery are quoted separately by our sales desk.
Contact Us
Questions about fit, coating choice or lead time go to our technical desk. Send the part number, the wavelength, the beam diameter at the optic and the intended incidence angle, and you will get an answer that names a specific part rather than a range of options. Bulk and project quantities are quoted individually.








Reviews
There are no reviews yet.